MILIM (주)미림씨스콘 MILIM SYSCON CO., LTD.

유틸메뉴

제품소개

RCTi 요약정보 및 구매

Designed for the permanently installed industrial market with all the advantages of Rogowski Coil technology

견적 및 구매 전화문의 031-776-2288
이메일문의 milimsys@milimsys.com
온라인문의 바로가기

제품 정보

상품 기본설명

Designed for the permanently installed industrial market with all the advantages of Rogowski Coil technology

상품 상세설명

RCT Industrial Current Sensor

RCTi and RCTi-3phase

The RCTi is a current transducer for permanent installation. Simple to install and easy to retrofit, the Rogowski (sense) coil is thin, lightweight, flexible and clip-around. The secondary output from the transducer is an instantaneous voltage proportional to the measured primary current providing an accurate, low cost, wide-band measurement of the primary current.

The RCTi is typically used with power and harmonic meters and analyzers, current meters, data-loggers, data acquisition cards, and in power quality applications.

The RCTi is available as a single channel transducer (RCTi) or as a 3 Channel Version (RCTi-3phase)

Related Documents

Overview

The RCTi is a current transducer for permanent installation. Simple to install and easy to retrofit, the Rogowski (sense) coil is thin, lightweight, flexible and clip-around. The secondary output from the transducer is an instantaneous voltage proportional to the measured primary current providing an accurate, low cost, wide-band measurement of the primary current.

The RCTi is typically used with power and harmonic meters and analyzers, digital multi-meters, oscilloscopes, data-loggers and data acquisition cards.

Standards and Approvals

  • CE marked
  • Complies with EMC EN 61326-1 2006
  • Complies with IEC61010-1:2001
  • PEM Ltd is an ISO9001:2008 registered company

Performance

Rated current (rms)
250Arms to 50kArms
Rated output (Full scale FS)
5.0Vrms (± 7.07V peak)
Output limit
150% FS (± 10.6V peak)
Supply voltage (wide input)
12Vdc (-10%) to 24Vdc (+20%)
Maximum input power
0.4W
Operating temperature range
–5℃ to +65℃ (Integrator electronics)
–20℃ to +80℃ (Coil and cable)
Bandwidth (-3dB)
(<2000A) 0.6Hz to 1MHz (300mm) 600kHz (700mm)
(>2000A) 0.2Hz to 1MHz (300mm) 600kHz (700mm)
Phase shift @50Hz
(<2000A) 0.9±0.1 degrees
(>2000A) 0.4±0.1 degrees
Accuracy (typ.)
±1.0% of reading
(5% to 150% FS, 25℃)
Output load
> 10.0 k ohm
Coil Length
300mm, 500mm or 700mm (Custom lengths available)
Cable Length (coil to integrator)
1m or 2.5m (Custom lengths available)

Features

  • Traceable calibration (certificate included)
  • No magnetic materials means excellent linearity < 0.1% reading
  • Fully isolated measurement
    • Isolated power supply 2kVdc
    • Coil rated at 2kVpeak (withstand test is 4kVrms / 50Hz / 60 sec)
  • Small DIN rail (or panel mount) enclosure – UL94V-0 rated

Options

  • IP65 die-cast aluminium panel mount enclosure (previously known as the IRF)
  • Isolated BNC-BNC cable split option between coil and electronics to enable ease of installation e.g. threading through existing conduit. Standard cable permanently fixed.

Applications

Induction Heating

In industrial induction heating applications the RCTi is often used to monitor both current amplitude and zero-crossing detection. Typically the RCTi provides the feedback signal to a voltage-fed medium frequency inverter, for example to an SCR firing control board. Measured currents range from 500A to 5,000A and the frequency varies from a few hundred Hz to 10kHz. The phase error of the measurement needs to be tightly controlled for accurate zero crossing detection. The RCTi has a very small and highly predictable phase error over this frequency range. In addition to its wide-band operation, the RCTi fits the application perfectly due to its easy installation, high reliability and small size.

Power Utilities and Renewable Technologies

Solar

The RCTi-3ph unit has been deployed in energy storage systems at the electrical grid distribution / residential level (120V / 240V, split-phase, 60Hz) to help mitigate the effects of high levels of penetration of PV (Photovoltaics) in neighbourhood supplies. These effects include load shifting, peak shaving and solar firming. The RCTi measures currents of 250A (RMS, sinusoidal), 60Hz nominal, 59.3 - 60.5 Hz range, with harmonics of interest up to 40th harmonic (2.5kHz). The RCTi-3ph unit is used to measure and report the grid/load current back to the controller of the storage system. The RCTi measurement allows for better control and management of power and energy flow in the system via the derivation of reported variables such as, power (active, reactive, apparent), power factor angle, as well as net energy usage.

The RCTi enables easy hook-up (particularly with the BNC option allowing easy cable installation through conduit) and has a simple output to the A/D on the data acquisition board with minimal scaling required. Finally it has an internal isolated supply in to separate control grounds which allows for reductions in EMI through simple shielded cabling and grounding.

Wind Energy

RCT Industrial Sensor Applications

Similar to the solar application the RCTi has been permanently installed in a sub-station connecting the electrical grid to an offshore wind-farm. The RCTi is mounted on various incoming feeds, they are all screened cables but the installations range from 132kV / 600A to 690V / 6,000A. A number of these feeds are outdoor, and PEM has supplied our RCTi transducer with suitable insulation for long term outdoor installation. The RCTi is connected to a portable power quality monitor and this in turn to a wireless transmitter which sends data about the load current on a continuous basis back to the sub-station control centre (e.g. magnitude, power factor, harmonic strength etc).

High Voltage DC (HVDC) Applications

The RCTi can be used in a wide variety of HVDC operations. Ostensibly it is used to monitor the steady state ac current inside the valve/switching enclosures. However it is also capable of monitoring large overloads with very high di/dt (over 1000A/µs) for protection purposes. The RCTi transducer is particularly suitable for this application as there is no loss of accuracy or damage when monitoring these over-load surges.

Other applications include

  • VSD motor drives and generators
  • Large pumps and compressors
  • Building services
  • Custom versions
    • Rogowski coils immersed in transformer oil
    • Long coils and cable runs
  • 당사제품 바로가기
  • 성남본사 오시는 길
  • 김포공장 오시는 길
  • 토지문화제를 응원합니다
모바일 버전으로 보기